THANKS TO OUR SPONSOR!

THANKS TO OUR SPONSOR!
Your Ad here
Be sure to sign up for the weekly RV Travel Newsletter, published continuously every Saturday since 2001. NOTE By subscribing to RVTravel you will get info on the newest post on RV Tire Safety too
. Click here.
Huge RV parts & accessories store!
You have never seen so many RV parts and accessories in one place! And, Wow! Check out those low prices! Click to shop or browse!

Friday, October 26, 2012

Gauge accuracy

If you are reading this blog you know that along with others, I constantly complain that people do not always maintain their tire pressure.

One part of the process is using a sufficiently accurate gauge. I consider +/- 2 to 3 percent or +/- 1psi when measuring passenger tires to be sufficiently accurate.

Over the past few years I have checked more than 40 different gauges and have observed a 14 to 18 percent failure rate in two groups of 20 or so gauges.

I have two digital "Master " gauges as seen to the right, which read to 0.5psi increment. Both have been checked against ISO certified laboratory gauges and one reads 0.5 psi high and the other 0.5 low. I compare these gauges to each other to confirm they have not gone out of calibration before I conduct my gauge test. I figure the chance of both going out of calibration the same amount and same direction at the same time is very unlikely.

This year while at the Gypsy Journal Rally in Celina, OH, at my Tire Basics seminar, I offered to check gauges. Here are the results.

Actual         Indicated      Type Gauge             Error
82.0                81                Dial                       -1%
70.0                69                Dial                       -1%
77.0                75                Stick                     -2.6%
76.0                81                Dial                       +6.6%   Fail
77.0                92                Short Stick            +19.5%  Fail
74.5                81                Long Stick             +8.2%    Fail
79.5                78                Long Stick             -1.8%
77.5                78                Long Stick             +0.6%
68.5                72                Long Stick             +5.1%   Fail
68.0                68                Dial                         =
68.5                74                Long Stick              +8%   Fail

As you can see we observed a 45 percent failure rate with all the "fail" gauges giving a high reading which could result in the operator unknowingly operating their tires in an under-inflated state yet thinking the tires were properly inflated.  Given the general tendency for RVs to be overloaded in the first place or to be operated right at the limit of the load capability for the specified inflation this is definitely not the better way for a gauge to be wrong.

Having your own accurate "master gauge" is not unreasonable given the low cost of good quality digital gauges. You don't even need a special dual foot master gauge.

Do your own "calibration check" by using the "master single head gauge to check a front tire. Then use your "truck" dual foot gauge (as seen on the left in the top picture above ) to get a reading on the same tire to confirm the reading. If the readings match you can be confident all your readings will be sufficiently accurate when you use your dual foot gauge on the rear tires.

I would suggest you get a digital gauge and then visit the tire store from one of the major tire companies and ask if they would check your digital against their master certified gauge. You could also ask when their master was last calibrated. A competent certification includes affixing a dated calibration sticker to a master gauge. If they cant tell you when it was calibrated just say "thank you" and go to a more competent  tire dealer.

Finally don't just throw your master gauge in the bottom of your tool box. I suggest you keep it in a box of some type. Even a Tupperwear type container can protect your master gauge.

Also don't forget to always use a cap or screw on TPM sensor to keep dirt out of the valve core area of your valves. If you don't understand why you need a cap on the valve I suggest you subscribe to this blog as I will be posting a story showing exactly why you should always protect the valve core.

Edit:   I have conducted similar evaluations at FMCA Conventions in Perry, GA  in 2016 and Madison WI in 2015. At those events I tested about 50 gauges and found between 10% and 16%  were off by more than 5 psi.

2 comments:

  1. I have one of those digital guages just like the one you show. I pump up all the tires to the proper levels but then when I turn on the TPS system there is a variance of a couple of pounds some high and some low. Should I be concerned? The manufacturer says that is normal that they all vary a bit. My biggest concern is that it shows me when pressure is going low fast such as a leak or potential sudden blowout. We traveled 8500 miles this summer and things where perfect since I monitered the tires using the system. Also carry a small air compressor for top offs before moving the coach in the morning...only had to do that twice. I think part of my luck was buying quality tires. Firestones. They gave me no trouble.

    ReplyDelete
  2. I also see pressure reading variation in two different TPM systems that I do not see with the calibrated gauges. TMPS is intended to give warning of inflation changes during operation. They are not intended to be substitutes for having an accurate pressure gauge.

    ReplyDelete

Thanks for your comment. We look at each one before posting to keep away the spammers.