THANKS TO OUR SPONSOR!

THANKS TO OUR SPONSOR!
Your Ad here
Be sure to sign up for the weekly RV Travel Newsletter, published continuously every Saturday since 2001. NOTE By subscribing to RVTravel you will get info on the newest post on RV Tire Safety too
. Click here.
Huge RV parts & accessories store!
You have never seen so many RV parts and accessories in one place! And, Wow! Check out those low prices! Click to shop or browse!

Friday, May 18, 2018

ST tire Belt Separation "Autopsy" "How To"


This info is from an inspection I did a while ago. Some may find it informative.  A friend wrote a post on an RV Forum of his experiences and the results of my "Cut Tire Inspection". He posted:

[image]"This summer I had a tire failure, 3 actually in all by the time I was done. If you are into the details of tire failures, this is one type of tire failure. This is a little long of a post, but there are lots of pics to go with the words and some background.
I'm not a tire expert by any means, just a machinery guy trying to figure out what went wrong with my rig so I did not repeat the same problem and could correct what went wrong. So I took this one as far as I practically could.

I caught the first failure here in my yard doing axle maintenance. When I jacked up the camper to put it on jack stands, my left rear tire would not clear the ground on the normal stand height. H’mm OK what’s up?

[image]
I looked at the left rear tire and it looked more round across the face than I remembered. I still did not know what the issue was at this point.
 [image]



I jacked it up some more and started to take the tires off. I took all 4 tires off and I could see one tire, the left rear looked different. It was more curved across the face of the tire than the rest. Laying it on the ground it showed up more not be square to the sides.

Here is a normal one

 [image]
After comparing the other 3 to this one rear left I measured the OD of the tire. Yup, it is 1” larger in OD circumference. OK, something let loose inside this tire.
 I put this bad tire aside, finished up the axle work, and put the spare on. I then tried to figure out what was wrong with this tire. Looking on the outside I really did not see anything much that was wrong with it other than about 180 degrees around the outside, the tire progressively was getting larger in OD up to a high spot then starting coming back down. Whatever was wrong with it created an out of round tire.

 [image]

I demounted the tire and looked inside. Nothing really looked wrong to me inside. I happened to have a fellow RV buddy who is a retired tire engineer who has done tire failure analysis for most of his career. We hooked up and he told me how to section the tire and send it to him. So here is how we did this. He told me how to cut out the side walls. I was shocked you can cut up a side wall this easy. There is an inherent danger in doing this. Heavy gloves and a sharp knife is a must. Once you start cutting it out it sort of unzippers. You start above the tire bead and cut towards the OD, then start and cut around the circumference.
[image]
Now I had a donut. The hard part is cutting through the steel wire in the tire. Ideally, you do this on a vertical band saw with a progressive tooth blade. The rubber wants to bite and grab the blade. I did not have a large enough vertical band saw so I used a Sawzz All. Here one really has to clamp this thing down or the rubber will grab and start shaking the saw violently. You do not want any blade pinch as the rubber bites into the blade. Need to back flex it to keep it pulling apart as you cut. I clamped it to some old sawhorses and cut it apart.

[image]
[image]
Now I looked at the cross-section. Well, nothing real exciting at the 90-degree point from the high point.



[image]
 So I curled up the sample to fit in a box I could UPS to him. Here it is
[image]
I  sent him the tire and then started to investigate if I did something wrong to cause this failure. I always check tire pressure and run max cold sidewall pressure at the start of every trip. I even have my own small compressor in the truck if I need it. So under inflation was not the problem.

I also do not tow faster than 60 mph. I do not need to, big truck or not this is a safety limit for me. So I was not overrunning the 65 mph max speed rating creating excess heat.

I use white tires covers when the camper is at home. These tires are 3.5 years old at this point. I can say the first year they were only 50% covered until I have my present tire covers in place. There really was not much tire cracking. No sidewall cracks, some very fine in tread cracks and there were several stone cuts in the valleys of the treads.

Next was weight. I had not been to the scales in about 1.5 years and I added some upgrades. So I loaded the camper with stuff for a campout and full freshwater as we do haul water to some camps. I went to the scales and weighed each axle with WD engaged. I could not get each wheel position at the scales so when I came home I used my force jack to get each wheel position. Here is the weight chart.
[image]
The failed tire location has 12.5% extra tire capacity or 318# from the max load. There is some error in this data as my force jacked weighed a little heavy. It did, however, show me that the 4 tire locations are different. The front axle was pretty equal, the rear axle very different. My fresh tank sits right over the front axle which may have had something to do with the front being more even. At this point, the weight did not seem to point to a glaring problem.

Since I could not find anything wrong, yet anyway, I bought a new Maxxis tire for the spare and we headed off on vacation. My tire buddy also was on vacation so he did not yet have my tire done.

On vacation, I was 800 miles from home on the NYS Thruway and while gassing up, OMG… This tire right side rear tire does not look good. Dang, it looks like the failed one. So we pulled over in the truck lot and took it off and put the spare on. Yup, it let go too like the 1st one.


[image]
I was lucky a 2nd time I caught the failure before it let go. If you are going to have to change a tire on the road, the NYS Thruway makes a good changing spot… OK so now I have no spare…. I’m thinking of where I can get one when I get to my Mom’s house. Well…. No luck finding one close by. We did make it home OK. Another 800 miles.

When we made it home I was already working on changing tires to LT tires. When I jacked up the camper to take off the ST’s, OH boy, another one…. The tread bulged. This tire would not even roll correctly it wobbled so bad it would fall over.
[image]
So I dodged the 3rd bullet. I could not see this when it was on the camper, only when I took the weight off. The damage did not yet progress far enough yet or it was not out in the open where I could see it.

Soon my tire engineer buddy was done investigating the 1st tire I sent him. The tire failed for what is called “detachment” or what is nicknamed sometimes “slipped belts”. It is where the tread separates where the steel belts are in the tire tread from the main tire. Basically the tire unbonded itself inside the tread. Here are his analysis pictures.

He sectioned the tire sample I sent him and knowing what to look for starting to see clues of the problem. You can see small separations at the yellow arrows.

His description was “Cut 1 was my initial cut away from the identified bulge area. There are small detachments identified. If this was all that was found in the tire it would not be a serious issue.”
[image] 

Then he sectioned again and he found the entire area let go.
His description was
“Cut 2 location was identified by careful measurement of tread depth and I found a location with more wear than in other areas. The large detachments between the belts on both shoulders can be seen”


[image] 

 [image] 
[image] 
 [image]
His description was “Detach 1a & 1b show the length of the detachment to be over 11" long” 
 And this one really shows the detachment separation.

[image]
His description was “Detach Width shows the width of the two detachments relative to the tread width”
asked him how did this happen? His response:

Why detachment?
There are several things that can cause this. They would primarily be a breakdown of the rubber that coats the steel. This could be due to a manufacturing error or simply the selection of a lower strength rubber which cannot tolerate the forces applied to the tire. Only lab testing can determine that. Sometimes detachments can be initiated by tread cuts or punctures but that does not seem to be the case of the tire I inspected. Detachments are one of the more difficult conditions to analyze as there is a need for a lot of additional background information and data.


From this investigation, I have a perfect case to file a report with the NHTSA as I used the tires within the ratings. I have since filed 3 complaints, 1 for each tire. I’ll create a thread on how to do this filing. It is the only way we as RV’ers can help this cause of trailer tire failures become more known to the right people who can help. See here How To File a Tire Failure Complaint

There is now a growing understanding that for tandem trailer applications that a 20% more tire capacity reserve is needed to help hold up to the service of a multi-axle trailer. In my case I am towing heavy, I am not overloaded, in relation to my tire capacity. When I upgraded I targeted to get as close as I could to the 20% reserve at the heaviest loaded tire. I had a choice of load Range E in the ST or go to 16" LT and deal with tire wheel well issues. I weighed the options and went LT. See here for more on the LT change ST225/75R15 to LT225/75R16 Conversion

While LT tires may not be for everyone, knowing your weights of each tire location and where you are in relation to the tire capacity reserve is something you can do. You can also not tow over 65 mph on ST tires, keep them at max sidewall cold pressure at the start of each trip and use white tires covers over them when the camper is in storage.

I hope this helps someone in the future.

 

 

2 comments:

  1. I ran ST225/75R15 D tires which came with our RV trailer GVWR 7985 lbs. 2000 miles on tires and running a TPMS from day one with no warning from TPMS the tire blew. Damaged the finder well. I switched to E series and continue use of my TPMS but have had 2 tires ( from RF tandem and RR ) with huge side wall bubbles within 1000 miles. I too only run 55/60 mph. But when I exceeded to like 70 mph momentarily to pass the truck would act like I had a front truck tire that was out of balance. It was by chances I noted the first side wall bubble while inspecting the tires at a rest stop. I changed the bad tire to the spare. The truck shimmy stopped. Made it home put a like new tire on the trailer. 2 weeks later the 2 tire (RR) gave the truck the same shimmying. I stopped st the rest area and sure enough another side wall bubble.
    These are off shore mfg tires. (No more for me) I am going to try good year Endurance tires. If they cause a problem good year can deal with it. In both cases the tire people said road hazards caused the side wall desperations.

    ReplyDelete
  2. Sidewall bubbles could indicate low inflation relative to the load. Have you confirmed your actual tire loading with truck scale measurement? Have you confirmed your tire gauge is +/- 5 psi accurate? TPMS low pressure set to 60 psi?

    ReplyDelete

Thanks for your comment. We look at each one before posting to keep away the spammers.