THANKS TO OUR SPONSOR!

THANKS TO OUR SPONSOR!
Your Ad here
Be sure to sign up for the weekly RV Travel Newsletter, published continuously every Saturday since 2001. NOTE By subscribing to RVTravel you will get info on the newest post on RV Tire Safety too
. Click here.
Huge RV parts & accessories store!
You have never seen so many RV parts and accessories in one place! And, Wow! Check out those low prices! Click to shop or browse!

Tuesday, May 15, 2012

What do you think about temperature guns? Part 1

I get asked that question.

This can get technical so if you don't want to get bogged down, the answer is - IR guns are OK for metal objects or for surfaces with uniform temperatures but not for getting accurate tire tread area temperatures.

Now for those that want the details.
I see some who claim on RV forums that the guns are a good tool to help determine the proper tire inflation for their RV. I own an infrared (IR) gun I got from our favorite cheap tool store, Harbor Freight. So you might expect I use it all the time. While I did use the gun for my Tire Cover Test, I have only used it once on my tires and that was during my study to collect data so I could offer this observation on using IR guns for monitoring tire temperatures.

During my career as tire engineer I have used needle probes on Indy racing tires for drivers like Mario Andretti and Al Unser. These probes were designed to penetrate into the tire to the top of the body cord which is the hottest location. If I did not probe deep enough I would get a misleading low temperature. An error of just a few degrees could be critical.

I have also been involved with the use of thermal imaging systems costing tens of thousands of dollars, to conduct tire design tests, so I know from personal experience that they can provide information on the operating temperature of a tire under load and at speed. What I also know is that different parts of a tire can have a very large temperature variation. If a tire is going to fail or be damaged due to excess heat, it is not the average temperature of a tire but the temperature of the hottest spot that may cause the damage.

To help you understand what I am talking about let’s look at some thermal images captured by a laboratory quality IR system. These images are from a book “The Pneumatic Tire” by Gent & Walters, distributed by NHTSA in 2006. The 707 page book is aimed at tire engineers and chemists, so it is definitely not a quick read while at your campsite. While I did consult a very little bit with a couple of the engineers and scientists that contributed to its writing, the majority of this information came from very experienced members of the tire industry community, some of whom worked for different major tire companies and others who have PhD’s in their field and others who teach college and graduate level chemistry or tire mechanics courses. These guys know their stuff.

IN THIS SERIES OF IMAGES, you can see the variation in temperature both with inflation level and across various portions of the tire being tested. I have added yellow circles approximately ½” diameter. I think you can see that it is essentially impossible to find a uniform temperature over such an area especially when increased temperature differential becomes more important.

The lab IR equipment has a very high resolution which means it can differentiate temperatures across very small areas, 0.10” or smaller. To help, green is 90°F and white, or hottest, is 140°F. It is important to also remember that rubber is a good insulator and does not transfer heat rapidly, so it takes minutes at a constant load and speed for the higher temperatures generated deep within the tire structure to migrate and stabilize at its surface which is constantly being cooled by the surface air.

You should note that different portions of the tread pattern have very significantly differences in temperature with the highest temperatures deep down in the bottom of the grooves, slots and sipes of the pattern. To obtain these higher temperature readings it is necessary for the IR sensor to “see” down into these tread pattern features while also not including the much cooler temperatures only 0.10” to 0.25” away and to be able to record the temperature while the tire is running. It is also important to notice that as you move away from the tread pattern and down to the smoother sidewall, the temperature gets much cooler. So if you try and use your hand held gun on a more temperature uniform portion of the tire you will no longer be reading the hot locations.

IF YOU HAVE USED YOUR HAND HELD IR GUN to learn the temperature of your tires, I think you can see that you have been mislead, as the area used to sense the surface temperature was too large to capture just the hot area in the tread area, or you targeted the more uniform but much cooler sidewall of the tire. In either case your readings do not provide a reliable or sufficiently accurate reading to be used for tire inflation setting measurement.

I am sure that some still think that they have made the effort to be very precise when taking temperature readings. They always shot the exact same location (i.e. the same tire lug for they vary in size and therefore vary in temperature) on each tire, were only a ½” or less away from the tire surface to get the hot location in the bottom of a slot, and that the time to measure all their tires was always less than 30 seconds after stopping and always in the same sequence to address the surface cooling that all tires go through, or maybe not.

So, in my next post, I will show the results and analysis of the test of pressure variation effect on temperature I ran with the manager of race tire development at a major tire company, who was gracious enough to assist me in doing a comparison of my TPMS that reads the contained air temperature (CAT) using a probe mounted inside the tire vs. a hand gun vs. his professional 0.1° F reading probe which gets into the rubber and provides a reading closer to the source of the temperature.

5 comments:

  1. Aside from the discussion of temp guns, I found your inset photos to be very enlightening, Roger. It is obvious even to an untrained eye like mine that tire pressure has a visible and dramatic effect on tire temperatures.

    The noticeable rise in temperature (even if it is only surface temps) between 41 psi and 11 psi is alarming. That is the moral of the story anyway, isn't it? Don't ride on underinflated tires! Thanks for a fascinating post.

    ReplyDelete
  2. I use an IF gun to take tire and wheel hub measurements. However, I also use a TPMS to monitor my tire pressures. The IF gun is mainly to track wheel hub temps. When shooting tires with an IF gun, people should not be concerned about absolute numbers but rather major differences between tires and hubs on the same side. Sun side versus shade side will make a big difference. When using my IF gun, I am looking for something that is alarmingly different, higher in temperature than all of the others.

    ReplyDelete
  3. Roger, it is obvious to me you have made rocket science out of a simple semi-quantitative indicator of operating tire condition. What ever the reason, an IR indicated high temperature (maybe <140F or so) would dictate the need for some further investigation. This is not a race tire. It is a large tire on a motorhome operating at 60 mph or so, for example, where a slightly higher temperature may only indicate the sunny side of the coach. BUT it would certainly indicate: Hey, at least look at the tire, does is seem low? Check the air pressure, which will be higher than cold, we hope. See, if not do something. We are not concerned about your racing tire measurements of plus or minus 1 or 2 or 5 degrees. Get real. The IR temperature measurement is a good quick check at the rest area to say. hey, everthing looks normal!

    Merl Bell
    Chemist of 58 years

    ReplyDelete
  4. Merl You are correct.
    I tend to go into too much detail. The point I was trying to make was that IR guns are not the proper tool to use to establish or set your inflation.
    They have their uses but using their temperature reading as a guide for establishing cold inflation is not one of them.

    ReplyDelete
  5. I think they are a valuable tool to compare one tire to another, or one wheel bearing to another. If only to have a bit of confidence things are normal. I would use a air gauge to measure tire pressure.

    ReplyDelete

Thanks for your comment. We look at each one before posting to keep away the spammers.